Launched in 2003, this very special Focus featured a unique wide arched body shell, 8x18” OZ alloys, uprated Sachs suspension, Brembo 320mm 4 pot brakes, Quaife ATB equipped MTX75 gearbox, uprated AP clutch, and a turbocharged zetec engine (labelled Duratec) featuring sodium cooled exhaust valves with uprated valve springs, low compression Mahle pistons, uprated water pump and a Garrett Gt2560 turbocharger. As standard the car features a water cooled charge cooler, and running 0.8bar boost makes around 220bhp running on Ford’s own EEC V engine management.

focus-rs-nms

Power Upgrades

Stage 1 - 270bhpStage 2 - 300bhpStage 3 - 340bhpStage 4 - 400bhpStage 5 - 450+bhp
A very simple upgrade performed on an otherwise std car, consisting of uprated Garret actuator, uprated spark plugs, panel filter in the std airbox and an uprated recirc dump valve. The car is remapped keeping the std boost control solenoid, midrange boost is mapped at 22psi tailing to 16psi at the limiter. This results in huge midrange torque increase to 300lbf ft, whilst power climbs to 270bhp!
Custom Remap
NMS custom ECU remap
Huge Midrange Torque
Increased to 300lbf ft
Expected BHP gains
Expected 270bhp
Improved driveability
Smooth power delivery
On top of stage 1 we add our tubular thick wall exhaust manifold and a full decat stainless exhaust system. We also recommend changing both the boost and water hoses to a new set of silicone hoses. (originals are prone to splitting) The car is remapped and now runs 1.8 bar midrange, tailing to 1.4 bar at limiter. Midrange torque increases to 340lbf ft!
Custom Remap
NMS ECU remap
Strong Midrange Torque
Increased to 340lbf ft
Expected BHP gains
Expected 300bhp
More Boost
1.8 Bar midrange boost
NEW Exhaust Manifold
Tubular Exhaust Manifold
NEW Exhaust System
Decat Stainless Exhaust
Reduced lag
Reduced lag & More Responsive
Improved driveability
Smooth power delivery
Stage 3 consists of everything in stage 2 but we fit an uprated fuel system which includes an external swirl pot mounted under the rear of the car, feeding a Bosch 044 pump and modified fuel lines. A new larger turbo is added along with a new downpipe to mate with the existing stainless system. The charge cooler radiator is replaced with a larger aluminium item to increase charge cooler efficency. We keep the std air box and uprated recirc dumpvalve as these items give the best drivability and prevent stalling and stumbling with the Std MAF sensor. The engine is again remapped to 28psi midrange tailing to 22psi at the limiter. Midrange torque is now 380lbf ft!
Custom Remap
NMS custom ECU remap
NEW Fuel System
Including Swirl Pot
Expected BHP gains
Expected 340bhp
Improved Cooling
larger Aluminium Cooler
NEW Turbo
NEW GT28r Turbo
Huge Torque
380lbf ft Midrange Torque
Reduced lag
Reduced lag & More Responsive
NEW Downpipe
Improved Exhaust Flow
This is the absolute limit of the standard engine and clutch provided they are in good condition! At this power we are at the limit of lifting the head (due to M10 head bolts) and the limit of standard con-rods. The standard engine management is no longer adequate at this power level, because the MAF sensor is unable to give stable flow readings during heavy wheelspin conditions (when the driver has to feather the throttle) and hence the car is prone to jerkyness and flat spots. As such we convert the car to speed density (i.e. map sensor) using OMEX 600, but maintain the original ecu to continue operation of the dashboard and OBD functionality. A large bore exhaust manifold and Garrett T38 or GT30 turbo are fitted along with a custom downpipe and 3 inch exhaust system. Along with the additional items fitted at stage 3, the car is remapped and improves all aspects of drivabilty, idling, cold starting and performance over the standard management! Boost is mapped to around 30psi, and midrange torque of 420lbf ft is not uncommon!! If the car has covered more than 50,000 miles an uprated clutch will also be required, and we recommend the Sachs motorsport items!
Custom Remap
NMS custom ECU remap
Improved driveability
Smooth power delivery
Expected BHP gains
Expected 400bhp
NEW Management
OMEX 600 Management
NEW Turbo
NEW T38/GT30 Turbo
Huge Torque
420lbf ft Midrange Torque
Reduced lag
Reduced lag & More Responsive
NEW Exhaust
Improved Exhaust Flow
Power gains above 450/500BHP are completely achievable, however it would be best to contact us to discuss your project and advise accurately what is requirements for this sort of power. For more information you can also take a look at out engine builds section which talks more about what we do to build engines which can produce this sort of power.
Engine Builds Contact Us